As with many other connectors, it has been adopted for uses other than originally intended, including as a DC power connector, an RF connector, and as a connector for loudspeaker cables. The RCA connector was initially used for audio signals. The jack has a small area between the outer and inner rings which is filled with an insulator, typically plastic (very early versions, or those made for use as RF connectors, used ceramic). The ring on the jack is slightly smaller in diameter and longer than the ring on the plug, allowing the plug's ring to fit tightly over it. Devices mount the socket ( female jack), consisting of a central hole with a ring of metal around it. The ring is often segmented to provide spring gripping pressure when mated. In the most normal use, cables have a standard plug on each end, consisting of a central male connector, surrounded by a ring. Other uses Ĭomposite video cable with RCA male plugs for the Xbox 360. Refinement of the RCA connectors came with later designs, although they remained compatible. In the 1950s, RCA connectors began to replace the older quarter-inch ( 1⁄ 4 inch) phone connectors for many other applications in the consumer audio world when component high-fidelity systems started becoming popular during the transistor revolution. Three lower-cost 1939 television models had an audio output connector on their rear panel instead of an integrated amplifier and speaker: RCA TT-5, Westinghouse WRT-700, GE HM-171. In 1939, RCA introduced two radio- television floor consoles (TRK-9, TRK-12) which used the same internal connection concept but the audio output of the television chassis was connected to the radio/amplifier chassis via a male to male cable. RCA later marketed a special turntable for 45 RPM records, the model 9JY. The connector was labelled on the back of radio with one of the following terms: " Victrola", " Phono", "Pick-up", "Television". īy no later than 1938, RCA migrated the female connector to the rear panel of many of their desktop AM radio models to allow customers an easy method to attach an external phonograph or television at a later date. Originally, the concept was intended as an easy method to unhook sources while troubleshooting the console during servicing. The amplifier chassis had female connectors which accepted male cables from the radio chassis and phonograph player. Plug here."īy no later than 1937, RCA introduced this design as an internal connector in their radio- phonograph floor consoles. Tag reads "An inexpensive RCA Victor record player will make a fine Victrola of this radio. Rear panel of a 1939 RCA model 45EM vacuum tube desktop AM radio with a female RCA jack. RCA jacks are often used in phono inputs, a set of input jacks usually located on the rear panel of a preamp, mixer or amplifier, especially on early radio sets, to which a phonograph or turntable is attached. The word phono in phono connector is an abbreviation of the word phonograph, because this connector was originally created to allow the connection of a phonograph turntable to a radio receiver. The connectors male plug and female jack are called RCA plug and RCA jack. The name RCA derives from the company Radio Corporation of America, which introduced the design in the 1930s. The RCA connector (or RCA Phono connector or Phono connector ) is a type of electrical connector commonly used to carry audio and video signals. I never see the blue decoding light come on with optical input from my iMac.RCA plugs for composite video (yellow) and stereo audio (white and red) Just as a point of reference, when I plug a SPDIF connector from an HDTV into the back of the same receiver I get the Blue Multi-Channel Decoding light as expected from a major network or PBS station. BTW, the iMac is a mid 2011 model running the latest version of El Capitan 10.11.1 as follows:įYI: My Sony STR-DA2ES surround sound receiver says that I’m getting a linear PCM signal, not 5.1 through the optical cable, even with a 5.1 source. Once I restart the Audo MIDI Setup my iMac has reset the audio back to 2-channel 24-bit. One immediate hint about problems setting up “Encoded Digital Audio” is that I cannot configure speakers for 5.1, only stereo, no matter what I do. All steps seem fine until setting “Encoded Digital Audio” I get silence through my Toslink cable after doing that.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |